Shepherd boy
Sub-grazing is not always used and some fishermen do not consider it necessary. It is located next to the hook. Necessary to change the appearance of the attachment and its general characteristics.
In addition, such a sinker creates quite a lot of problems, since it has a huge number of varieties and sizes, which does not allow you to choose the most suitable one the first time. The antenna allows you to notice the bite, but without a backup it will be quite difficult to load it.
Float rod for live bait fishing
Crucian carp most often lives in lakes and various reservoirs, and many fishermen go fishing specifically for them. You can also find crucian carp in small ponds. However, in order to catch such fish, you need to understand its behavior and how to properly equip your fishing rod to improve fishing efficiency.
How to properly equip a float rod for crucian carp?
There are two types of equipment:
- Flywheel;
Allows you to catch crucian carp at a distance of 10 or 15 meters and easily control the entire process. The principle of such equipment is quite simple: a fishing line with equipment is attached to the tip of the rod.
- Match.
It has a reel in its design, thanks to which you can make fairly large bait casts. You can also use a thin fishing line that the fish does not notice.
How to properly equip a float rod for carp?
Basic equipment is also suitable for carp fishing. However, there are also individual approaches that will make fishing more productive.
Equipment components:
- Float (with cambrics);
- Sinkers (lead);
- Leash;
- Hook.
By combining all the components together, you get an excellent rig that can lure and catch carp.
How to properly equip a float fishing rod with two hooks?
For such equipment, a piece of thin cambric (10 cm) is required. A fishing line is passed through it and tied to the two ends of the hook. The main line runs in the middle.
Proper float loading
Correct loading of the float (at the very beginning of the tip)
Some call this loading the float, although in fact it is correct to call it loading. You need to attach lead pellets to the fishing line so that only the upper part of the float (its tip) remains above the water.
If you have previously seen large floats in which most of the body sticks out of the water and anglers are trying to catch something on them, this is the wrong approach, unless the angler is catching pike with live bait (or any other fish, in which case the sensitivity of the equipment in general does not play a role and it is important that the live bait does not greatly distort the movement of the float with its presence).
How to load a float on a pond
Sensitive loading occurs as follows. You attach a small lead pellet under the float using pliers, pliers, needle nose pliers (last with your teeth). Throw it into the water. If the body of the float is still visible above the water, you need to add more weights.
Load the line with lead pellets until only the tip of the float appears above the water, preferably so that the body is completely under water. This will provide the best sensitivity. Although it is acceptable to have a small portion of the body visible above the surface in windy conditions, this will reduce visual deception as the float passes through the waves.
If you have loaded too much , use scissors, thin-nose pliers or tongs (teeth last, take care of the enamel) to pinch off a small piece of lead. Be careful not to damage the line.
How to load a float at home
Follow all the same steps, but use not water from a reservoir, but a 1.5 or 2 liter plastic bottle. Well, lower the float as close as possible to the lead pellets so that they do not lie at the bottom of the bottle when determining the additional load.
How to catch crucian carp with a fishing rod - all the secrets of catching the most common, but at the same time, finicky fish.
Catching carp with a float rod - preparing the right bait, choosing bait, fishing technique.
Choosing the right fishing line for float fishing once and for all.
How to increase your fish catch? ">
Over 7 years of active fishing, I have found dozens of ways to improve the bite. Here are the most effective ones:
- Bite activator . This pheromone additive attracts fish most strongly in cold and warm water. Discussion of the bite activator “Hungry Fish”.
- Increased gear sensitivity. Read the appropriate manuals for your specific type of gear.
- Pheromone -based lures .
How to rig a fishing rod
Many anglers prefer two rigging methods: sliding and blind installation. These two types of components are similar in assembly. The only exception is the float, which can be attached in different ways.
Line selection
A monofilament line is a more suitable option for catching fish over 1 kg, since a break may occur at the last moment of fishing. The fish will desperately resist. And the stretchable fishing line will not allow the tackle to break.
Fishing lines are produced in whole series for a specific purpose. For catching heavyweights and fishing in frosty conditions.
Manufacturers began to produce fluorocarbon fishing line to replace monofilament line. This line is more expensive in price. Its most significant advantage is its invisibility in the water. It becomes absolutely invisible to the fish, which increases the likelihood of fishing success. If you don’t have enough money to buy a reel, you can purchase several meters of fluorocarbon fishing line and tie it to the main one.
For match rods, the weight of the line is considered an important factor. Because fishing is carried out at a great distance from the shore and the possible wind can be annoying. Therefore, it is recommended to buy weighted options that float in the water.
When purchasing a braided fishing line, you may encounter the fact that during hooking the fish lip will break. The fish begins to flop around, a hole is formed in the place where the hook is caught and the prey can jump off. There is an important advantage - this is the opportunity to catch a truly massive specimen. Because the fishing line is not inferior to its analogues in strength.
Choosing a float
There are many floats available and it is difficult for beginners to make the right choice. In fact, all float models are designed for certain conditions and equipment. If, as an example, we consider fishing with a fly rod in a calm current, then we should make a choice for a moderate carrying capacity and weight of the float. They are attached tightly.
Long floats are highly sensitive. The advantage is that the float is capable of transmitting even the lightest touches of the fish to the bait. But there is also a drawback - the impossibility of fishing during windy conditions. There are ball-shaped models that are not afraid of wind, but their sensitivity is lower. The best option would be a drop-shaped float, since it is moderately sensitive to fish and weather conditions.
For long casts you need a float that has a large carrying capacity. It is equipped with a thick antenna. With such a weighted rig, you can cast 30 meters. The antenna must be bright so that the bite can be seen from afar.
Loading correctly
Modern loading can be provided in the form of a whole chain of fractions. Thanks to this, it is quite easy to adjust the immersion depth of the float by removing or adding pellets .
How to load correctly:
- The task of the sinker is to immerse the float in the water to the antenna mark.
- Additional small weights are designed to calibrate the float. Only the part that is painted in bright colors will remain. The correct weight of the load will not affect the bite, the fish will not even feel resistance.
- For beginners, it is better to use an olive-shaped sinker. And 4 auxiliary pellets are enough. They are secured at a distance of 5 cm from each other.
Selection of hooks
Experts recommend choosing small hooks, but they must be strong. The trick is that the fish can easily swallow the bait. But for larger specimens you should buy appropriate hooks.
Spicy is also equally important. And this is very difficult to determine. During Soviet times, most fishermen checked the point by running the hook along the nail. If after this a scratch remained, then the hook was considered sharp.
A sharp sting is necessary for hooking the fish's lips , as well as for stringing hard baits. For example, if you use pearl barley, an unpleasant situation will occur: even small roach can break off due to the fact that the hook tip does not even show through the bait, therefore, there is simply nothing for the fish to catch on.