Press mold for the production of technoplankton drawing

Where to buy a mold for technoplankton?

To save their time, enterprises involved in the production of fishing products have also launched serial production of this equipment.

Unfortunately, not all companies manufacture such structures. It is much easier to purchase such a product via the Internet from some fishing master who makes them for sale.

Almost all experienced fishermen prefer to use bait and groundbait made independently, since its composition is always precisely known. Home-made technoplankton is no different in terms of catchability than store-bought ones, and fish bite on it much better.

Do-it-yourself mold for technoplankton

In order to obtain such a design at home, you need to take the following materials:

  • The so-called pressing cup, which is a hollow metal tube, internal


    the diameter of which should not be too large, and the walls should be thick enough. Its maximum length is 10 cm. At one of its ends there should be a thread onto which the plug will need to be screwed;

  • The plug is made from a standard plumbing plug , which is used in the process of making water pipes in apartment buildings;
  • The pin is designed to make a hole : a hole is drilled for it in the central part, through which it will be mounted. There should be a blockage on the main tube;
  • The seal is made of a steel tube , its diameter is selected so that it easily fits inside the first tube. In length it should completely coincide with the base. A piston and plug are screwed into its upper part.

There are several methods for producing technoplankton in a microwave oven:

  • made of metal in the microwave , as this will damage it. It is best to use plastic tubes with a similar internal diameter;
  • Take two plugs so that they fit snugly at each end. One of them is installed on the bottom side, thanks to which the bait will be pressed. When the tube is completely filled with the appropriate composition, it is closed with another stopper and baked in the microwave for several minutes;
  • You can use an ordinary medical syringe , the capacity of which should be about 20 ml. The upper part is carefully cut off, filled with a nutrient mixture, plugged with a piston from another syringe, and then placed in the microwave for a few minutes.

What will you need?

To obtain high-quality technoplankton, two basic conditions must be met:

  • It should create a certain turbidity in the water column - bait particles should float closer to the surface so that the water becomes less transparent;
  • As a result of its use, dust must necessarily form when heavy particles settle to the bottom and pull a certain amount of turbidity from there.

It is not advisable to take too many components, as the silver carp may sense something is wrong and ignore the bait.

The following substances can be used as ingredients:

  • Filler (this element is flour obtained by grinding millet or corn, crackers ground into powder and a number of other products that can be ground to such a state);
  • Glue base (it should dissolve slowly in water - powdered sugar, dry cream, etc.);
  • Flavorings (they can be added both in dry and liquid form - strawberry, vanilla, caramel or honey);
  • Water (needed if the mixture is too dry and cannot be pressed properly. Half a gram of water will be enough for one cubic centimeter).

One of the most catchy recipes is the following:

  • Half a kilo of roasted peanuts;
  • Half a kilo each of semolina and corn flour;
  • A kilogram of fishmeal;
  • Sugar syrup made in a one to one ratio.

All ingredients must be thoroughly mixed until a homogeneous mass is obtained and sent for pressing.

Drawings and diagrams

Before you start manufacturing a mold, you need to develop its drawing or circuit diagram . This can be done by hand or in a special computer program. If you do not want to carry out such work, then you can find the corresponding pictures on the Internet, which are presented there in quite large quantities.

Moreover, there are corresponding video tutorials dedicated to making a mold for technoplankton with your own hands.

Bait production procedure

During the manufacturing process, one should not forget about a number of features of this type of bait, otherwise its effectiveness will be low or absent altogether:

  • Technoplankton must contain substances that create dust when it gets into the water. At the same time, they need to easily peel off the bait and gradually float up, forming a small dust cloud;
  • They take strong-smelling ingredients so that the fish finds the bait as quickly as possible by its delicious smell;
  • If you follow the advice of experienced fishermen , then it is best to use oatmeal as the basis for technoplankton, which does not dissolve in water too quickly;
  • It is not at all necessary to add flavorings to the bait , but with them the fishing efficiency will be even higher.

Read also: Device for punching holes in metal

The resulting mixture must be tested at home: the product is placed in a jar of water and observed how it behaves. If it dissolves too quickly, then a certain amount of starch is added to the mixture, which will reduce this indicator, making it quite acceptable.

Press for technoplankton

Without a press it is impossible to achieve a high result, since the mass, while in water, must gradually turn into a dust cloud.
Depending on the pressing method, you may need:

  • metal or plastic pipe;
  • cylinder or plug;
  • pin;
  • compression device;
  • ejector piston;
  • microwave;

At first glance, the product may seem technologically complex, but, in fact, anyone can make such bait at home.

There are two pressing methods:

Cold pressing:

  1. You will need any metal tube about 90 cm long.
  2. You need to select the appropriate cylinder for it.
  3. A hole is drilled in its lower part for a pin, which will be attached to the lower plug, threaded onto the lower part of the tube.
  4. Pour the mixture to the very top using a watering can and compact it.
  5. Separate the mixture from the molds. The result was a small but dense briquette.
  6. The mixture placed inside the tube is pressed using a vice or clamp.

Hot pressing:

  1. The mixture is placed in a plastic pipe with a tight-fitting stopper.
  2. The mixture is compacted by an ejector piston.
  3. Place it in the microwave for 30 seconds and set it to maximum power.
  4. After extraction, the mixture is compacted again.

How to use the mold?

At the first stage, prepare the appropriate mixture, mix it thoroughly so that it is as homogeneous as possible.

Then it is poured into the working cylinder, on one side of which a plug should be screwed. When the entire volume is completely filled, the mold is closed with another plug on which the piston is installed and carefully tightened.

If you do this jerkily or apply too much force, this can lead to the product failing : it may burst, in some cases the thread will break.

When the technoplankton is made, a hole is drilled in the central part through which the bait will be put on the hook. Its maximum diameter should be about half a millimeter.

Bait production procedure


Making technoplankton

First of all, you need to choose the right bait composition for technoplankton. You can use semolina or corn flour as a base. To form a dense structure, honey or granulated sugar is added.

The prepared mixture must be placed in the working cylinder with the base installed. After backfilling and preliminary compaction, cover with the top lid. The jack is installed with the piston facing up. There must be a supporting steel plate. To form a dense structure, a force of 4-5 tons is sufficient. If this indicator is exceeded, mechanical damage to the mold may occur.

Thanks to the smooth edges, removing the finished bait is easy. The main thing is that the rod does not damage the resulting cylinder.

The video shows an example of making technoplankton at home:

How long has it been since you had a really BIG CATCH?

When was the last time you caught dozens of HUGE pike/carp/bream?

We always want to get results from fishing - to catch not three perch, but ten kilogram pikes - what a catch! Each of us dreams of this, but not everyone can do it.

A good catch can be achieved (and we know this) thanks to good bait.

It can be prepared at home or bought in fishing stores. But stores are expensive, and to prepare bait at home, you need to spend a lot of time, and, to be fair, homemade bait does not always work well.

You know that disappointment when you buy bait or prepare it at home and only catch three or four bass?

So maybe it’s time to use a truly working product, the effectiveness of which has been proven both scientifically and in practice on the rivers and ponds of Russia?

Of course, it is better to try once than to hear a thousand times. Moreover, now is the season! A 50% discount on your order is a great bonus!

Fishing means something different for every lover of this type of recreation, but a fish on a hook in any case is a welcome end to it. In order for the bite to be successful, it is necessary to master a considerable number of subtleties. In particular, study the tastes of fish. For example, silver carp, as well as carp, small carp, carp, bream, roach, crucian carp or catfish can be caught using technoplankton. This is a briquette-barrel of a mixture of nutrients that gradually dissolves in water.

The effectiveness of fishing for technoplankton depends on:

  • quality and composition of technoplankton;
  • the concentration of nutrients in the cloud of food it produces;
  • whether the hooks are located directly in the cloud.

Self-production of technoplankton

Technoplankton is a relatively new bait designed specifically for catching silver carp. By the way, for now she is the only one. Silver carp do not bite on anything other than technoplankton (except purely by accident).


Recently, there have been a lot of enthusiastic fans of purposefully catching this fish using float tackle. Demand was born and supply appeared.

Quite a lot of ready-made technoplankton is sold on the market. The average price is 30 rubles for 1 “barrel”. One fishing trip takes from 10 to 15 units of technoplankton.

When calculating daily and monthly costs, fishermen have a desire to start fishing with homemade technoplankton.

Is it possible to make this bait at home, while saving your money? Yes, you can make technoplankton with your own hands at home. The question is different: is the game worth the candle?

If you catch silver carp on a float or bottom tackle at best once, or at most twice a month, devoting only a couple of months a year to this fishing, then you should not bother with making technoplankton yourself. It is more profitable to buy several packs of factory-made ones.

But if you go out to catch lizard regularly, making artificial plankton yourself makes sense.

Operating principle - how technoplankton works

The operating principle of technoplankton is simple. Several hooks suspended in parallel are attached to the hole for the equipment in the briquette. When the inhabitants of a reservoir swim to a cloud of food formed by technoplankton and begin to eat it, they do not see the hooks and swallow them.

The versatility of technoplankton lies in the fact that it is used both for catching fish at the bottom and on the surface with a float:

  • For fishing on the bottom, it is better to use instant plankton, which dissolves in about half an hour.
  • for float tackle or when there is no bite, it is better to use “long-lasting” types that dissolve for several hours.

They fish with this type of equipment from mid-spring to mid-autumn.

Composition of technoplankton

Technoplankton, which is logical, is made as attractive as possible for fish. The feed ingredients are selected in such a way that they have different specific gravity and buoyancy, respectively, due to which a different level cloud of nutrients appears in the water.

The composition of the finished technoplankton remains with the manufacturer. As for self-made, it is good to use the following ingredients in its composition:

  1. Fillers. Everything ground to flour - oatmeal, corn or popcorn, millet, buckwheat, peas (boiled or raw), breadcrumbs, dry cookies.
  2. Adhesive components (glue and do not allow to dissolve quickly). Dextrin, maltodextrin, technorapid, milk powder, cream powder, powdered sugar. It is better to use a mixture of maltodextrin and powdered sugar (there is literally a little less powder), rather than them separately.
  3. Flavors. Can be used in any form. It is necessary to add such an amount at which the kneading will be obvious and stable. Most of all, fish loves sweet aromas: honey, strawberry, caramel, vanilla, raspberry.
  4. Dissolution retardant. Typically starch or rice flour is used.
  5. Humidifier. Usually water is added.
  6. A bubbling ingredient helps create a geyser effect, which promotes the dissolution of components when placed in water (any effervescent tablets, baking soda + citric acid, dry kvass starter), ratio 1/6 to the total mass.

Homemade recipes

Any fisherman makes technoplankton for silver carp with his own hands according to his own recipe. At the same time, there are a number of the most popular compositions.

First recipe:


  • 250 grams of wheat flour;

  • 200 grams of corn flour (you can grind popcorn in a coffee grinder);
  • 200 grams of citric acid and soda;
  • 250 grams of semolina flour;
  • 350 grams of oat flour.

All components must be mixed and water added. When the mixture is plastic, you need to transfer it to a press and make barrels, or you can cook briquettes in the microwave. The effervescent composition must be added to this mass before pressing.

Second recipe:

  • 500 grams of corn flour;
  • 500 grams of semolina;
  • 350 grams of powdered sugar;
  • 350 grams of mamalyga;
  • 350 grams of breadcrumbs.

Everything needs to be mixed until smooth. Then gradually add honey solution. Then the briquettes need to be dried.

Third recipe:

  • any dry biscuits;
  • powdered milk;
  • one can of condensed milk.

Pour the condensed milk into a container and gradually add the dry ingredients until the composition reaches the consistency of sour cream. Cookies and milk must be added in equal proportions. Place all this in the freezer for 30 minutes. Then take out and knead the frozen dough, again adding dry ingredients in the same ratio. Bulk ingredients must be added a little at a time; if you add a large amount, the dough will thicken very quickly. Then you need to add a little water to make it sticky. Finally, we rub everything through a sieve and press.

The fourth recipe for bottom fishing:

  • 150 grams of ground roasted peanuts;
  • 500 grams of dog food;
  • one glass of sugar;
  • 70 grams of black pepper.

If you want to use this recipe for float fishing, you will need to add more dry ingredients. When bottom fishing, everything can be left unchanged.

Fifth recipe:

  • any combination of ground breadcrumbs, cereal flakes and dry cream;
  • 0.5 tbsp. l. honey;
  • 300 grams of fruit jelly.

Mix the jelly with honey, then gradually add the dry mixture until a moist (but not wet) composition is formed. The pressed briquettes must be placed on a napkin until they are completely dry.

Sixth recipe:

  • 300 grams of raw sunflower seeds;
  • 300 grams of flour;
  • 200 grams of rice flour;
  • 200 grams of wheat flour;
  • 150 grams of dry cream;
  • a glass of corn flakes.

All ingredients must first be ground using a coffee grinder. Afterwards, the components are mixed and placed under a press.

Seventh recipe:

  • 200 grams of shortbread cookies;
  • 200 grams of sunflower seeds;
  • 200 grams of boiled peas;
  • 150 grams of milk powder;
  • 200 grams of semolina;
  • 200 grams of food for aquarium fish;
  • flavoring;
  • 150 grams of protein powder.

All components need to be crushed and mixed. For bottom fishing or fishing in the current, you can add a small amount of clay.

Eighth recipe:

  • 300 grams of rice flour;
  • 500 grams of corn flour;
  • 300 grams of buckwheat flour;
  • 300 grams of pea flour;
  • 300 grams of unroasted peanuts;
  • 300 grams of baby food;
  • honey syrup;
  • 300 grams of raw peeled seeds;
  • 150 grams of cucumber flour.

Recipes for making your own technoplakton

Each fisherman makes the composition in his own way, but there are several of the most popular mixtures, which we will focus on.

Recipe 1:

  • 200 grams of corn flour (you can make it from popcorn ground in a coffee grinder);
  • 200 grams of wheat flour;
  • 300 grams of oatmeal flour;
  • 200 grams of semolina flour;
  • 150 grams of soda + lemon juice.

All ingredients must be mixed and sprinkled with water. When the dough becomes plastic, it must be placed in a press and made into briquettes, or it can be baked in a microwave oven. The effervescent mixture must be mixed with the mass immediately before pressing.

Recipe 2:

  • 0.5 kg of raw semolina;
  • 0.5 kg corn flour;
  • 300 grams of breadcrumbs;
  • 300 grams of mamalyga;
  • 300 grams of sugar.

Mix everything until smooth and dilute with honey solution, gradually.

Recipe 3:

  • 1 can of condensed milk;
  • Powdered milk mixture;
  • Powder cake.

Pour a can of condensed milk into a bowl and gradually stir in the dry ingredients until the mixture reaches the consistency of sour cream. Milk and cake should be added in equal quantities. Place this in the freezer for half an hour. Then we take it out and knead it into a tight dough, again adding dry ingredients in equal quantities. Add the bulk part a little at a time; if you add a lot at once, the dough may thicken too quickly. Moisten slightly with water to make it sticky. At the end we pass it through a sieve and press it.

Recipe 4 for feeding on the bottom:

  • 0.5 kg of dog food;
  • 100 grams of roasted ground peanuts;
  • 50 grams of dry sweet pepper;
  • 1 cup powdered sugar.

If you want to use this recipe for float fishing, add more dry ingredients.

Recipe 5:

  • 250 grams of ready-made fruit jelly;
  • 1 tsp. honey;
  • Any combination of crushed cereal flakes, breadcrumbs and powdered milk.

Read also: DIY hydraulic presses

Mix the cooled jelly with honey, and then gradually add the dry mixture into it until a moist (but not wet) mixture is formed. Place the compressed barrels on a napkin to dry completely.

Recipe 6:

  • 350 g ground flour;
  • 350 g raw sunflower seeds;
  • 150 grams of wheat flour;
  • 150 grams of rice flour;
  • 1 cup corn flakes;
  • 100 grams of milk powder.

First grind all components to a powder using a coffee grinder, and then mix.

Recipe 7:

  • 250 grams of sunflower seeds;
  • 150 grams of shortbread cookies with creamy taste;
  • 125 grams of dry cream;
  • 250 grams of cooked peas;
  • 250 grams of fish bait;
  • 250 grams of semolina;
  • 125 grams of protein powder;
  • Flavoring.

Grind all ingredients and mix.

Recipe 8:

  • 0.5 kg corn flour;
  • 250 g rice flour;
  • 250 g pea flour;
  • 250 g buckwheat flour;
  • 250 g milk baby food with rice;
  • 250 grams of raw peanuts;
  • 250 g raw sunflower seeds without peel;
  • Honey syrup.

Recipe 9:

  • 1 tbsp. Sunflower seed;
  • 150 grams of dry cookies with vanilla flavor;
  • 250 grams of chopped popcorn;
  • 250 grams of semolina;
  • 250 grams of corn flour;
  • 250 grams of milk powder;
  • 125 grams of cucumber flour.

To make cucumber flour, you need to grate the cucumber, dry it and then grind it. The flour has a fairly strong aroma, which attracts silver carp well.

Recipe 10:

  • 4 parts flour for hominy;
  • 4 parts millet flour;
  • 1 part rice flour;
  • 1 part milk powder;
  • Vanilla flavored sugar syrup.

Mix everything, adding syrup periodically. The total syrup should be added to about 30% of the total mass. Then let the mixture rest for 60 minutes. And at the end, we pass through a coarse sieve, press and dry.

Sugar syrup: 1 part water + 1 part sugar + vanilla, boil everything for 20 minutes and cool. If you need to increase buoyancy, add crushed cork.

How to increase your fish catch?

Over 7 years of active fishing, I have found dozens of ways to improve the bite. Here are the most effective ones:

  1. Bite activator . This pheromone additive attracts fish most strongly in cold and warm water. Discussion of the bite activator “Hungry Fish”.
  2. Increased gear sensitivity. Read the appropriate manuals for your specific type of gear.
  3. Pheromone -based lures .

Top 5 best recipes for making technoplankton with your own hands

To begin with, it is worth noting that today, drawings for creating homemade products and special devices are already available in sufficient quantities. It won't be difficult for you to find them. It is only important to strictly follow the rules that will be indicated in the article.

First set

Ingredients:

  • buckwheat flour - 0.2 kg;
  • oat flour - 0.2 kg;
  • corn flour - 0.4 kg;
  • breadcrumbs - 0.2 kg;
  • sugar - 0.1 kg;
  • 0.1 l of water.

Cooking method:

  1. First you need to prepare a syrup from sugar melted in water.
  2. Next, all other components are mixed in a separate container.
  3. The syrup is poured into the resulting mixture in a gentle stream, and then thoroughly blended with a blender.
  4. There's just a little bit left to do. Pour the technoplankton into the mold and compress everything.

Second set

Ingredients:

  • corn flour - 0.5 kg;
  • semolina - 0.05 kg;
  • chopped roasted peanuts - 0.5 kg;
  • fish powder - 1 kg;
  • effervescent mixture - 0.45 kg.

Cooking method:

  1. Mix all dry ingredients.
  2. Next, you need to create a syrup from sugar, as already mentioned in the first method of preparing bait.
  3. Pour the syrup carefully into the resulting mixture and mix everything well using a mixer.

Third set

Ingredients:

  • corn flour - 0.2 kg;
  • oat flour - 0.3 kg;
  • semolina - 0.2 kg;
  • effervescent mixture in the form of substances to create a geyser (as already 0.2 kg; mentioned earlier) - 0.15 kg.

Cooking method:

  1. Mix all dry ingredients.
  2. Then it is recommended to sprinkle the homemade product with plain water and you’re done.

Fourth set

  • heat-treated flour - 0.2 kg;
  • tear - 0.2 kg;
  • milk powder - 0.2 kg;
  • crushed dill seeds - 0.02 kg;
  • citric acid - 0.015 kg;
  • starch - 0.06 kg.

Cooking method:

  1. Mix all dry ingredients.
  2. Next, you need to pour in a little water and bring the composition to a homogeneous state.

Fifth set

Ingredients:

  • semolina - 0.5 kg;
  • corn flour - 0.5 kg;
  • milk powder - 0.5 kg;
  • breadcrumb powder - 0.3 kg;
  • hominy - 0.3 kg;
  • powdered sugar - 0.3 kg;
  • honey - 0.05 kg;
  • effervescent mixture - 0.4 kg.

Cooking method:

  1. Mix all ingredients except honey until smooth.
  2. Honey is added last, and the moisture content of the composition must be taken into account.

Press for the production of technoplankton

To prepare technoplankton at home, you need to get a press.

There are several types of presses for its manufacture:

  1. Pressing with a manual screw press.
  2. Squeezing with a jack.
  3. Using a high pressure hydraulic press.
  4. Pressing in the microwave.

Simple cold pressing mold:

  1. Glass for pressing. You need a metal tube 8-10 cm long with a small diameter and a thread at the end for screwing on the plug.
  2. Cork. A screw-on plug for water pipes can be used as a plug.
  3. Pin for a hole in the tackle. You need to drill a hole in the plug cap and fix a thin but strong pin in it to make a hole in the finished barrel. Screw the plug onto the main tube.
  4. Seal. To compact the substance, you need to select a metal cylinder of such a diameter that it fits tightly and easily into the tube. The length of the cylinder should be the same as that of the tube. You can also screw a plug onto the inner piston cylinder from above.

Scheme of work:

  1. Screw the plug onto the main tube.
  2. Fill the tube with the mixture.
  3. Insert the piston.
  4. Clamp the structure using a bench vice, jack or clamp.
  5. Remove the piston and unscrew the cap from the tube.
  6. Push out the resulting barrel of technoplankton.

For pressing in the microwave, you can use several options:

  1. Using a plastic tube. From a plastic pipe of small diameter (about 30 mm, maybe smaller), you need to cut a piece of about 4-7 cm. Then you need to select 2 plugs that will tightly close both ends of the tube. Immediately close one end with a stopper and stuff the mixture tightly. Close the other end with a stopper and bake in the microwave. You can simply try to tightly fill a piece of tube without lids and put it in the oven. But with one lid, this form is much more convenient to fill out.
  2. Using a syringe. You need 2 disposable syringes with a volume of 20 ml. Cut the syringe from the side of the needle nose so that you get a cylinder. On the one hand, plug the syringe with a piston, fill it with the substance and, on the other hand, press it tightly with a piston from another syringe. Then you can leave the second piston, or you can remove it and put the cylinder in the microwave.

Making a mold for technoplankton

To make a basic cold pressing mold, you will need the following materials:

  • A pressing cup is a metal tube of small diameter, 10 centimeters long, with a screw thread at the end onto which a plug is screwed.
  • Plug - as a rule, a regular plumbing plug is used, which plumbers use to install water pipes.
  • Pin for making a hole - a small hole is drilled in the central part of the plug to fix a strong pin in it for mounting it in the finished barrel. A mash is installed on the main tube.
  • Sealant - a metal tube of similar diameter is selected so that it easily fits into the pipe. In size it should be the same length as the base itself. A plug is also screwed onto the piston, which is located in the upper part. For pressing work with further use of a microwave, there are several methods:
  • Using a plastic tube , a base of this material is taken, with a diameter of up to 30 (no more), and a piece of no more than 7 centimeters is cut off. 2 plugs are selected that tightly close both ends. One plug is tightly mounted on the bottom side and with its help the nutrient mixture is compacted. When filled, close with a second stopper and bake in the microwave.
  • Using a medical syringe - take two syringes with a capacity of 20 ml, cut off a small part from the side of the spout to make a cylinder. On one side, the cylinder is plugged with a piston, the nutritional composition is tightly placed and tightly closed with the piston from the second syringe. Place the cylinder in the microwave and bake.

What will you need?

For preparation, one should not forget two basic conditions:

  • The drug in the water should create turbidity (the added particles should float to the top and create an opaque effect).
  • It should create dust (when particles separate from the tablet, they sink to the bottom, and when they emerge, they drag dirt and turbidity from the bottom with them).

The components should contain no more than 4 - 5 components; an excess can create the opposite effect from the desired one.

The main ingredients that must be included in the “treat” for fish:

  • Fillers - flour is used, which is obtained by grinding certain cereals (millet, oats, corn), crushed crackers, cookies and other components that can be ground into flour.
  • The base is adhesive - components that are ideally pressed, but dissolve very slowly in water. They can be powdered milk or cream, or powdered sugar.
  • Flavorings - added in dry or liquid form, a certain amount should give a persistent attractive smell. Fish prefers sweet smells (strawberry, caramel, honey or vanilla).
  • Rice flour or starch - add them if the fish treat dissolves very quickly in water.
  • Water – if the edible barrel is difficult to press, half a gram of water is taken per unit. The end result is a hard and dry treat that is very difficult to break apart with your fingers, but in water it perfectly performs all its necessary functions.

Cold pressing and microwave, what's the difference?

During cold pressing, the prepared mixture is placed in a device and, using pressure, gives it hardness, turning it into a tablet barrel.

When pressing in a microwave, the energy of electromagnetic radiation is used. To do this, the substance is placed in a plastic tube with stoppers at both ends and baked until the desired state is reached for about 20–30 seconds. Instead of a tube, you can take a disposable large syringe.

As a result of using these two methods, you will get almost the same result.

Difference between different methods

During cold pressing, the mixture is placed into a device and, using pressure, the mixture is given hardness.

During pressing using a microwave, electromagnetic radiation is used. For this purpose, the mixture is placed in a tube and baked until the required state for approximately 25-35 seconds.

After using these methods, you will be able to get almost the same result.

Adviсe

  1. When preparing the mixture, pay attention to what type of fishing you are doing it for.
  2. At different times of the year, silver carp likes different flavors of bait.
  3. If the pond is heavily bloomed due to the heat, then the fish, on the contrary, will not be interested in feeding due to the abundance of food in the pond. During such periods, for fishing, look for bodies of water with clean water.
  4. When fishing with bottom gear, be sure to “raise” the hooks above the technoplanton using foam balls; when fishing with float gear, there is no need to hook them.
  5. If the current carries a cloud of food away from the hooks, then you can use a small sliding weight on the fishing line (cord) between the float and the rod. Be careful, when retrieving your catch, the tackle may become tangled.
  6. Don't forget to frequently replace your hooks with new ones or at least sharpen them before each fishing trip.

A group of fishermen revealed the name of the secret bait during interrogation.

The press mold for technoplankton (TP) allows you to make special baits for fishing with your own hands. TP looks like a cylinder, which contains various additives, baits, and flavor enhancers. A hole for a hook is provided along the central axis.

Read also: How to connect a conveyor belt with your own hands

What is this?

  • Technoplankton is a mixture of various components that are pressed into the shape of a small cylinder;
  • When technoplankton finds itself in water, the composition gradually comes into contact with it, becomes softer, and leaves a muddy trail of food;
  • The fish, which smells pleasant odors, begins to move towards the technoplankton, swallows it and ends up hooked;
  • The rate of decay of technoplankton can range from 15-20 minutes to several hours;
  • The decomposition depends on what the composition is made of and what components are included in it.

Purchasing technoplankton for fishing in specialized stores is very expensive. The price doesn't justify itself at all. At the same time, there are absolutely no difficulties in making a special press with your own hands. We invite you to figure out how to assemble the press and get a budget tool for preparing highly effective bait.

The nuances of making a press

Mold drawing

You don't need complex drawings to assemble the press. You can protect yourself with drawings and watch training videos, which will only benefit you when creating a high-quality form.

The main nuances of the assembly are the competent calculation of components and the choice of an effective pressing device. The most common bottle-type car jack performs well in the role of the latter.

The approximate dimensions of structural elements for technoplankton are as follows:

  • A hollow cylindrical shape into which the ingredients will be loaded. Choose the walls of the metal tube with a thickness of about 5 mm, and the height of the cylinder - 60 mm. An internal diameter of 27 mm is quite enough for preparing bait;
  • Support nickels. They should be made with an inner rounded surface. To ensure reliable support, provide a size 4-6 mm larger than the working cylinder. In the center, a rod is attached by welding, which is necessary to form a longitudinal hole in the TP. Usually the length is 5 cm;
  • Upper element of the press. Choose a cylinder with an outer diameter of about 27 mm, depending on the inner diameter of the hollow cylinder. That is, they should be the same.

If you correctly select all the components of the structure that fit perfectly together, you will get technoplankton of excellent quality. You will be able to produce bait that is smooth, beautiful, and dense enough for successful fishing. For comparison, the price of a finished press is 1000 rubles.

How to cook technoplankton

To prepare technoplankton with your own hands, having special molds at your disposal, you need to follow a few simple recommendations and consistently carry out all operations.

  1. Choose the appropriate composition for preparing future bait. There are a huge number of recipes, so you will have to use an experimental method to select the composition specifically for your region or body of water. Or consult with experienced fishermen, find out what fish bite best. This is already your task.
  2. Semolina or corn flour is usually used as the basis for preparing TP. To make the composition more dense, add a little sugar or honey.
  3. The prepared composition is loaded into the working cylinder.
  4. After filling the mixture, tamp it down a little and cover with the top lid.
  5. Install your bottle car jack with the stem facing up. In this case, do not forget about the need to use a steel support plate.
  6. To obtain technoplankton of sufficient density, it is enough to press the cylinder with a force of up to 5 tons. If the force is higher, you may damage the assembled mold. This is another powerful argument in favor of do-it-yourself presses. Beginners often do not calculate the load, which is why the new product breaks. I have to shell out about 1,000 rubles again to make bait for the fish.
  7. The smooth edges of the press machine ensure free exit of the finished technoplankton from their cylinder. Sometimes it makes sense to brush the edges with flavored oil. It will definitely prevent technoplankton from getting stuck in the cylinder, plus it will give additional attractiveness to the bait in the eyes of the fish.

Making a mold for technoplankton

When it gets into the water, the cylinder begins to dissolve, forming a light suspension that imitates natural plankton. But for repeated use it is necessary to achieve maximum bait density. Therefore, before making your own, you need to choose the right mold.

You can make a similar press design with your own hands or purchase a ready-made model. In the first case, you will need to correctly calculate the dimensions of all components. For pressing, you can use a bottle car jack.

Dimensions of components:

  • hollow cylinder. Inner diameter – 27 mm. Wall thickness – 5 mm. The optimal height may be 60 mm;
  • support nickel. Must have a rounded inner surface. To create reliable support, it is recommended to make the overall dimensions 4-5 mm larger than those of the working cylinder. A rod is welded in the center, which will form a longitudinal hole in the technoplankton. Its length is usually 50 mm;
  • upper part of the press for technoplankton. The outer diameter of this cylinder must coincide with the inner diameter of the supporting one - 27 mm. It is also recommended to make the inner edges oval.

These components must be carefully matched to each other. After pressing, technoplankton has smooth edges and a dense structure.

The average cost of a ready-made mold is 800-1000 rubles, depending on the size and material of manufacture.

Secrets of a good catch

Technoplankton is mainly used to catch the following types of fish:

At the same time, it is quite possible to catch a number of other representatives of the underwater world using technoplankton. By making a cylindrical bait of a smaller size, bream, rudd, crucian carp, etc. can easily be used on it.

There are several techniques that allow a fisherman to be more confident that he will not return empty-handed from fishing.

  1. Use bite activators when fishing. Many do not trust modern means based on the use of various additives and ready-made mixtures for bait. In practice, their production is based on an analysis of the behavior of fish, its reaction to various components. A striking example is how fishing is activated when using chocolate-flavored bait.
  2. Use high-sensitivity equipment when biting fish. When the water is turbulent, or a rather tricky fish is being caught, the fisherman does not always notice the beginning of the bite due to rough equipment. By increasing the sensitivity of the float, the percentage of fish that fall off the hook will drop sharply.
  3. Don't use hooks that are too big. Many fishermen, in pursuit of a big catch, rely on a large hook. They believe that small hooks will not be able to hold a large trophy. In fact, this works in reverse. A small hook allows you to catch fish of various sizes. The main thing is that it swallows the bait, that you hook it correctly, and that the fishing line can support the weight of the catch.
  4. Pheromones are excellent at stimulating increased activity. Another example of modern developments for fishing. Most importantly, they work great. The main thing is to choose a pheromone that is suitable specifically for the fish that is found in the reservoir. Or the fish you set your sights on when you go fishing.

Nuances of preparing and using technoplankton

To ensure that the cylinders of prepared technoplankton work effectively, listen to a few tips for catching fish with this bait.

  • Studying various recipes for preparing technoplankton, we can conclude that there is no universal composition. Therefore, you should experiment with the compositions;
  • The buoyancy of technoplankton is one of the main points worth paying attention to;
  • When fishing from the bottom, bran or finely chopped wine cork should be added to technoplankton;
  • If you plan to use technoplankton for fishing below the surface, use more flour in the composition. This will allow technoplankton to leave behind a muddier trail that attracts fish;
  • When fishing for silver carp in the summer and on hot days, use flavorings or natural ingredients of garlic and honey when preparing the technoplankton composition;
  • In autumn and spring, fish bite better on the smells of herbaceous components. Therefore, add them to technoplankton.

Fish is not the main thing in fishing. But who doesn’t want to go fishing and come back with a whole fish tank?! To do this you will need an effective bait and a little luck.

Rating
( 2 ratings, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: tourirana@cp9.ru
Для любых предложений по сайту: tourirana@cp9.ru